Skip to content

Double Carbon FD503 · Supplied by DBSilco

FD503-TG30

Thermally conductive, two-part silicone for potting inductors and power modules.

1:1 A:B by weight 10 or 25 kg per component

Red silicone dispensed into an electronic module
Illustrative image: red silicone potting an electronic module.
Thermal conductivity
≥3.0 W/m·K
Mixed viscosity
8,000-15,000 cps
Working time
At least 30 min
Hardness
Shore A 40-60

Double Carbon · FD503-TG30

Material properties

Open TDS

Before cure

Material type
Two-component addition-cure silicone
Appearance
Component A: red fluid; Component B: white fluid
Viscosity
8,000-15,000 cps per component
Mixed viscosity
8,000-15,000 cps
Mixing ratio
1:1 by weight
Working time
At least 30 min

After cure

Hardness
Shore A 40-60
Thermal conductivity
At least 3.0 W/m·K (ASTM D5470)
Dielectric strength
At least 15 kV/mm
Volume resistivity
At least 1.0 × 10¹³ Ω·cm
Density
3.0 ± 0.1 g/cm³

Cure schedule

Curing time
No more than 6 h at an unspecified temperature; no more than 60 min at 80°C

The TDS permits room-temperature or heated cure. It lists ≤60 min at 80°C and a separate ≤6 h value without a stated temperature.

Contact DBSilco to confirm the temperature and schedule for your selected grade before evaluation.

Red silicone dispensed into an electronic module
Illustrative image: silicone potting application.

Applications

Inductors and electronic components

FD503-TG30 offers thermal conductivity of at least 3.0 W/m·K for inductors and power modules, with a mixed viscosity of 8,000–15,000 cps.

Processing steps from the TDS

Technical data sheet
  1. Prepare components

    Both components must be stirred separately until uniform. A different tool for each container keeps A and B from mixing too early.

  2. Mix & degas

    Mix equal weights of A and B (1:1) until uniform. Remove trapped air under vacuum for 1-3 minutes before pouring.

  3. Dispense

    TG30 has at least 30 minutes of working time after mixing. Pour before it thickens, using a layer at least 0.5 mm thick.

Material compatibility

The data sheet lists PC, PP, ABS and PVC plastics, as well as metals. The stated operating temperature range is -40°C to 200°C.

The TDS specifies a minimum applied thickness of 0.5 mm.

Materials that affect curing

Release agents, plasticizers, rosin flux, condensation-cure silicones and amine-containing materials can prevent TG30 from curing properly.

Test conditions

Tests on the uncured material used 25°C and 55% relative humidity. The mechanical and electrical figures apply to fully cured samples.

Technical data sheet
Storage and compliance

Shelf life: 12 months in sealed drums, stored dry at 0–35°C.

The TDS states RoHS compliance. Contact DBSilco before ordering to confirm which current reports are available for this grade.

Data notes & compliance

Packaging and storage

FD503-TG30 is supplied as separate A and B components.

Component A
10 or 25 kg drums
Component B
10 or 25 kg drums
Mixing ratio
1:1 A:B by weight
Shelf life
12 months, sealed and dry at 0–35°C

Example: 10 kg A + 10 kg B provides 20 kg of mixed material. Confirm the pack size and quantity in your quotation.

Packaging and ordering details

Data sheet

Compare all five

Buy from DBSilco

Get a quote for your FD503 order.

Email the grade, quantity and delivery destination. We’ll confirm pricing, A/B pack sizes and delivery terms.

Grade not selected? Include your application and required properties.

Sales email

sales@dbsilco.com