Skip to content

Double Carbon FD503 · Supplied by DBSilco

FD503-TG101

Low-viscosity, two-part silicone for power modules and electronic components.

1:1 A:B by weight 10 or 25 kg per component

Illustrative gray silicone material in a mixing cup beside a cured sample
Illustrative image: grey potting material. Not a grade-specific product photograph.
Thermal conductivity
≥0.9 W/m·K
Mixed viscosity
2,500 ± 1,000 cps
Working time
At least 30 min
Hardness
Shore A 45-55

Double Carbon · FD503-TG101

Material properties

Open TDS

Before cure

Material type
Two-component addition-cure silicone
Appearance
Component A: grey fluid; Component B: light yellow fluid
Viscosity
2,500 ± 1,000 cps per component
Mixed viscosity
2,500 ± 1,000 cps
Mixing ratio
1:1 by weight
Working time
At least 30 min

After cure

Hardness
Shore A 45-55
Thermal conductivity
At least 0.9 W/m·K (ASTM D5470)
Dielectric strength
At least 15 kV/mm
Volume resistivity
At least 1.0 × 10¹³ Ω·cm
Density
1.72 ± 0.05 g/cm³

Cure schedule

Curing time
No more than 6 h; cure temperature not specified

The TDS permits room-temperature or heated cure. Its ≤6 h entry does not state a cure temperature.

Contact DBSilco to confirm the temperature and schedule for your selected grade before evaluation.

Grey potted power supply in an aluminium housing
Illustrative image: silicone potting application.

Applications

Power modules and electronics

FD503-TG101 combines low viscosity with thermal conductivity of at least 0.9 W/m·K for power modules and electronic components.

Processing steps from the TDS

Technical data sheet
  1. Prepare components

    Components A and B need thorough stirring in their separate containers. A different tool for each component keeps them from mixing too early.

  2. Mix & degas

    Mix equal weights of A and B (1:1) until uniform. Then remove trapped air under vacuum for 1-3 minutes.

  3. Dispense

    The mixture has at least 30 minutes of working time. Pour before it thickens, using a layer at least 0.5 mm thick.

Material compatibility

The data sheet lists PC, PP, ABS and PVC plastics, as well as metals. The stated operating temperature range is -40°C to 200°C.

The TDS specifies a minimum applied thickness of 0.5 mm.

Materials that affect curing

Release agents, plasticizers, rosin flux, condensation-cure silicones and amine-containing materials can stop the silicone curing properly.

Test conditions

The uncured values come from tests at 25°C and 55% relative humidity. The mechanical and electrical figures apply to samples that have fully cured.

Tensile strength
At least 1.0 MPa (GB/T 528)
Elongation
At least 50% (GB/T 528)
Coefficient of linear thermal expansion
No more than 220 ppm/°C (ASTM E831)
Technical data sheet
Storage and compliance

Shelf life: 12 months in sealed drums, stored dry at 0–35°C.

The TDS states RoHS compliance. Contact DBSilco before ordering to confirm which current reports are available for this grade.

Data notes & compliance

Packaging and storage

FD503-TG101 is supplied as separate A and B components.

Component A
10 or 25 kg drums
Component B
10 or 25 kg drums
Mixing ratio
1:1 A:B by weight
Shelf life
12 months, sealed and dry at 0–35°C

Example: 10 kg A + 10 kg B provides 20 kg of mixed material. Confirm the pack size and quantity in your quotation.

Packaging and ordering details

Data sheet

Compare all five

Buy from DBSilco

Get a quote for your FD503 order.

Email the grade, quantity and delivery destination. We’ll confirm pricing, A/B pack sizes and delivery terms.

Grade not selected? Include your application and required properties.

Sales email

sales@dbsilco.com