Skip to content

Double Carbon FD503 · Supplied by DBSilco

FD503-TG60S

Low-viscosity, flame-retardant silicone for battery electronics and power modules.

1:1 A:B by weight 10, 20 or 25 kg per component

Flame rating: V-0 (UL 94), as listed in the TDS.

Illustrative gray silicone material in a mixing cup beside a cured sample
Illustrative image: grey potting material. Not a grade-specific product photograph.
Thermal conductivity
Not listed in TDS
Mixed viscosity
600-1,200 cps
Working time
30-60 min
Hardness
Shore A 25-35

Double Carbon · FD503-TG60S

Material properties

Open TDS

Before cure

Material type
Two-component addition-cure silicone
Appearance
Component A: grey fluid; Component B: white fluid
Viscosity
600-1,200 cps per component
Mixed viscosity
600-1,200 cps
Mixing ratio
1:1 by weight
Working time
30-60 min

After cure

Hardness
Shore A 25-35
Dielectric strength
At least 15 kV/mm
Volume resistivity
At least 1.0 × 10¹² Ω·cm
Density
1.30 ± 0.03 g/cm³
Flame-retardant rating
V-0 (UL 94), as listed in the TDS

Cure schedule

Curing time
2-5 h; cure temperature not specified

The TDS permits room-temperature or heated cure. Its 2–5 h entry does not state a cure temperature.

Contact DBSilco to confirm the temperature and schedule for your selected grade before evaluation.

Cylindrical battery cells supported by potting material
Illustrative image: silicone potting application.

Applications

Batteries and power modules

FD503-TG60S is a low-viscosity silicone for battery electronics and power modules; its data sheet lists a UL 94 V-0 rating.

The TDS lists UL 94 V-0 but gives no thermal-conductivity value, test report number or specimen thickness. Ask DBSilco about supporting reports. The rating does not cover finished assemblies.

Processing steps from the TDS

Technical data sheet
  1. Prepare components

    Components A and B need thorough stirring in separate containers. Each component needs its own tool to avoid mixing them too early.

  2. Mix & degas

    Mix A and B at 1:1 by weight until uniform. Remove trapped air under vacuum for 1-3 minutes.

  3. Dispense

    The mixture has 30-60 minutes of working time. Pour before it thickens, using a layer at least 0.5 mm thick.

Material compatibility

The data sheet lists PC, PP, ABS and PVC plastics, as well as metals. The stated operating temperature range is -40°C to 200°C.

The TDS specifies a minimum applied thickness of 0.5 mm.

Materials that affect curing

Release agents, plasticizers, rosin flux, condensation-cure silicones and amine-containing materials can stop TG60S curing properly.

The mixing instructions specify 1:1 A:B by weight. The table also mentions volume, but no volume ratio is confirmed.

Test conditions

The uncured values come from tests at 25°C and 55% relative humidity. The mechanical and electrical figures apply to fully cured samples.

Technical data sheet
Storage and compliance

Shelf life: 12 months in sealed drums, stored dry at 0–35°C.

The TDS states RoHS compliance. Contact DBSilco before ordering to confirm which current reports are available for this grade.

Data notes & compliance

Packaging and storage

FD503-TG60S is supplied as separate A and B components.

Component A
10, 20 or 25 kg drums
Component B
10, 20 or 25 kg drums
Mixing ratio
1:1 A:B by weight
Shelf life
12 months, sealed and dry at 0–35°C

Example: 10 kg A + 10 kg B provides 20 kg of mixed material. Confirm the pack size and quantity in your quotation.

Packaging and ordering details

Data sheet

Compare all five

Buy from DBSilco

Get a quote for your FD503 order.

Email the grade, quantity and delivery destination. We’ll confirm pricing, A/B pack sizes and delivery terms.

Grade not selected? Include your application and required properties.

Sales email

sales@dbsilco.com